15W700 79th Street
Burr Ridge, IL 60527
PH: (630) 986-1600
FAX: (630) 986-1669

Direct Lift

Home Mfg. Links People Search Table of Contents Document Index

Direct Lift Solenoid Valves
1/8" to 1" FNPT or BSPT
Zero to 10,000 psig
-420°F to +500°F
 
These valves are used where small flows are needed. The magnetic pull of the coil opens the internal orifice directly by lifting the plunger assembly off the valve seat. Since these valves depend entirely upon the magnetic power of the solenoid for operation, the higher the pressure differential, the smaller the internal orifice must be. The orifice size available also depends on the viscosity of the fluid and the voltage requirements. Some applications would be:
 
bulletDirect injection of additives to a process
bulletAir ejection of a part from a mold or die
bulletHigh pressure cleaning of a small surface area
bulletSmall vacuum systems

This type valve operates from zero to a maximum specified operating pressure (see chart below).
NOTE: These valves must be mounted in a horizontal pipeline with the solenoid coil on top.
 
Maximum Pressure Differential (PSID)
Series Construct. Material Pipe Sizes Orifice Size Air/Gases Liquids Light Oil Steam
(1) 1000 # Angle 316SS 1/8"-1/4" 1/16"-3/16" 5000 5000 5000 300
(1) 2000 # Angle 316SS 1/8"-1/2" 1/32"-3/16" 10,000 10,000 10,000 300
3000 Globe Bronze 1/4"-1/2" 1/16"-3/16" 1500 1500 1500 250
      3/4"-1" 1/16"-3/16" 1000 1000 1000 250
(2) 13,000 Angle 316SS 1/4"-1/2" 3/64"-1/8" 2500 2500 2000 300
(1) 14,000 Angle 316SS 1/4"-3/8" 1/16"-1/8" 3000 3000 3000 200
(1) 15-794 Angle 316SS 1/2" 1/2"   350 (LCO2)    
16,000 # Globe 316SS 1/4"-1" 1/16"-3/16" 6000 6000 5000 300
50,000 Angle 316SS 1/8"-1" 1/16"-3/16" 2500 2500 2500  
Notes:
* Indicates valve always has a Class H coil as a standard feature. Series 1000, 2000, 13000, 14000 & 16000.
(1) Normally-Closed ONLY.
(2) Available in 3-way configuration.
# These valve series require a double-wound coil and Type "R" Relay for pressures above 1,500 psi. Consult Factory.

Maximum Pressure Differentials shown are for AC Voltages with the smallest orifice size. Consult the full catalog, local distributor or factory on DC Voltages and Normally-Open valves.

(4 pgs./164KB)
(4 pgs./143KB)
(4 pgs./87KB)
(4 pgs./179KB)
(2 pgs./111KB)
(2 pgs./144KB)
(4 pgs./151KB)
(4 pgs./133KB)
 

Teflon® and Tefzel® are registered trademarks of Dupont. Viton® and Kalrez® are registered trademarks of Dupont Dow Elastomers.

This page last updated: Wednesday, January 28, 2004
© Copyright 1998-2004 Fluid Process Control Corporation.
Information in this document is subject to change without notice.
Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.